Zivan NG7 Manuál s instrukcemi stáhnout pdf (Strana 2)

Visualization

Digital Instrument

During the

first minute after starting, on the digital instrument it will be displayed the value of the voltage drop on the output cable

To set the compensation value made by the charger to balance the voltage drop on the cables please follow the procedure

"Compens

ation setting of the voltage drop on output cables.

Compensation setting of the voltage drop on output cables.

During the lapse of time along which the digital instrument displa

it is

recommended to follow the below

Gauge the voltage drop at the ends of the output bars of the battery charger (close to the cover).

Gauge the voltage on the

Make the difference between the two values to get the voltage drop compensate.

Press shortly the MODE button (ROLL) until reaching the nearest voltage value to the desired one: it is possible to ROLL

parameters

between 0,0V e 1,5V with steps

Press long the MODE button (ENTER) to confirm

Ready Light

Charging status and current pha

PHASE

Phase 1

Phase 2

Phase 3

Phase 4

Phase5-

Phase6

End of charge

When using the remote visualisation through two

PHASE

Phase 1

Phase 2

Phase 3

Phases 4-5-

6 & End charge

S/S or alarm

IMPORTANT: according to the charging curve used maybe some phases are lacking.

NG5-7-9 CAN Bus Interface

Visualization

Digital Instrument

first minute after starting, on the digital instrument it will be displayed the value of the voltage drop on the output cable

To set the compensation value made by the charger to balance the voltage drop on the cables please follow the procedure

ation setting of the voltage drop on output cables.

After one minute from the starting the digital instrument will display the string of the

following parameters:

• BATTERY VOLTAGE (two-tone red upper led).

• CURRENT provided by the charger (two-tone red lower led).

• TIME in hours lacking to the end of charge (two-

tone green upper led).

• Ah supplied (two-tone green lower led).

• CONNECTED GADGETS (no two-tone led on -

only on a MASTER battery charge).

By pressing once the MODE button, the parameters' sequence

is blocked and it will be kept the

last value displayed. By pressing again on the MODE button the sequence of parameters

restarts.

Compensation setting of the voltage drop on output cables.

During the lapse of time along which the digital instrument displa

ys the voltage drop on the output cables (first minute after starting)

recommended to follow the below

-mentioned procedure: v

Gauge the voltage drop at the ends of the output bars of the battery charger (close to the cover).

Gauge the voltage on the

battery poles.

Make the difference between the two values to get the voltage drop compensate.

Press shortly the MODE button (ROLL) until reaching the nearest voltage value to the desired one: it is possible to ROLL

between 0,0V e 1,5V with steps

of 0,1V.

Press long the MODE button (ENTER) to confirm

Charging status and current pha

RED LED

GREEN LED

On Off

On with short flashing Off

On On with short flashing

On with short flashing spegnimenti On with short flashing

Phase6

Off On with short flashing

End of charge

Off On

When using the remote visualisation through two

-tone LED (AUX F -

Pin 1 e 2), the following signals are valid:

RED

GREEN

YELLOW

On Off

On with short quenching Off

Off Off

6 & End charge

Off On

Off Off

IMPORTANT: according to the charging curve used maybe some phases are lacking.

first minute after starting, on the digital instrument it will be displayed the value of the voltage drop on the output cable

To set the compensation value made by the charger to balance the voltage drop on the cables please follow the procedure

After one minute from the starting the digital instrument will display the string of the

tone green upper led).

only on a MASTER battery charge).

is blocked and it will be kept the

last value displayed. By pressing again on the MODE button the sequence of parameters

ys the voltage drop on the output cables (first minute after starting)

Press shortly the MODE button (ROLL) until reaching the nearest voltage value to the desired one: it is possible to ROLL

Pin 1 e 2), the following signals are valid:

YELLOW

Off

D01570-02

1 2 3 4 5

Komentáře k této Příručce

Žádné komentáře

Zivan NG7 Manuál s instrukcemi Strana 2

Komentáře k této Příručce

Související produkty a manuály pro Nabíječky baterií Zivan NG7